UL listed.Important SafeguardsWhen using an electrical appliance, basic precautions should always be followed, including the following. Read all instructions before using this appliance.Danger: To reduce the risk of death or injury by electric shock:Do not reach for appliance that has fallen into water. Unplug it immediately.Do not use while bathing or in a shower.Do not place or store appliance where it can fall or be pulled into tub or sink. Do not place or drop into water or other liquid.Always unplug this appliance from electrical outlet immediately after using.Unplug this appliance before cleaning.Warning: To reduce the risk of burns, fire, electric shock, or injury to person:An appliance should never be left unattended when plugged in.Close supervision is necessary when this appliance is used by or near children or invalids.Use this appliance only for its intended use as described in the manual. Do not use attachments other than those recommended by the manufacturer.Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the appliance to a Service Center for examination and repair.Keep the cord away from heated surfaces.Never operate this appliance with the air openings blocked or while on a soft surface, such as a bed or couch, where the air openings may be blocked. Keep the air opening free of lint, hair, and the like.Never drop or insert any object into any opening.Do not use outdoors or operate where aerosol (spray) products are being used, where oxygen is being administered or near flammable liquids, such as certain flammable blade lubricants or cleaning agents.Do not use this appliance with a damaged or broken comb or blade set, as injury may occur.Do not place or leave appliance where it may be damaged by an animal or exposed to weather.To disconnect, turn all controls to off then remove plug from outlet.Save The InstructionsThis clipper was designed for commercial use.CordThe cord should not be used to pull the clipper. Since freedom of movement needs to be maintained, care should be used to keep the cord untwisted and unobstructed. When stored, the cord should be coiled and the unit placed in original box or storage pouch (if provided).If your clipper has a polarized plug: To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug fits in a polarized outlet only one way. In the event the plug does not fit fully in the outlet, reverse the plug. In the event it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.Proper Use and Maintenance InformationThis unit is designed for commercial use. It is normal for the unit to become somewhat warm during normal use.Avoid pressing the blades strongly against the skin, being especially careful around the ears. The blades should be directed toward the skin at a right angle but without a great deal of pressure.Oiling Your Clipper. Put a drop of Wahl oil on tips of the blade while the unit is running. Oil should be applied at least once a day. Always hold clipper in a downward position so that oil does not enter into the unit.Disinfecting Your Clipper. Brush hair from the blades and spray with CliniClip blade cleaner/disinfectant. Wipe off excess with a clean towel. Apply a few drops of oil. See #3 above.To clean the unit, use either a clean, dry or dampened cloth. Do not use benzene or thinner to clean the unit.Do not store the clipper in a wet or moist environment.To prolong blade life, do not use clipper on hair that is coated with a permanent wave solution or hairspray.Do not touch any of the internal mechanisms. If the unit should need repair, do not attempt to repair it yourself. The appliance has no user serviceable parts. Return it to Wahl Clipper Corp.Do not wrap cord around unit for storage. This may result in breakage or cracks to power cord.Standard Blade Removal and InstallationRemoving and Cleaning BladesTo remove the blades, hold the clipper firmly in your hand. Using your thumb, simply push the blades away from the front of the clipper. The blades and the mounting plate behind them will all come off in one piece.To clean hair that may have become clogged between the blades, brush between the blades with the cleaning brush provided. Always be sure to oil the blades after cleaning. See #3 above.Before replacing the blades on the clipper, make sure that the two spring wires are firmly seated in the notches provided and that the top blade moves freely. If these springs are not firmly seated, your clipper will not function properly and may make a very loud noise.Replacing BladeTo replace the blades, place the hook at the bottom of the blade set into the space provided on the clipper housing. Once it is seated, snap blade set to case. You will hear a click when the blades are fully in place.Texturizing/Notching Blade Installation and Removal Tool (Optional)Caution: When installing the texturizing/notching blade, take care not to apply force at the tips of the teeth with your fingers. Injury may result. Apply any necessary force below the blade teeth.Caution: When removing the texturizing/notching blade, use the removal tool (optional)*.If your unit does not include the texturizing/notching blade and blade removal tool, order from your beauty supply dealer or directly from Wahl.Apply force in the direction shown (in instruction manual). Note how the removal tool is positioned over the blade teeth and cupped in the hand to assure retention of the blade when the clipper body is gently pried away from the blades. Perform removal operation over soft surface (i.e. towel, cloth).*Injury may result if fingers only are used for removal.Finger Ring AssemblyLay finger ring under the power supply cord below the strain relief at rear of unit.Important: Cord must be disconnected from power supply before assembling finger ring.Wrap tab end of finger ring around cord.Twist tab 90ø and push through slot.Straighten tab and slide finger ring up strain relief until snug.The finger ring can be positioned for either left or right hand use.Slide finger ring off of strain relief so it moves easily.Rotate finger ring so is moves easily.Return finger ring to position.Attachment Comb AssemblyTurn unit off.Place comb over blade teeth.Rotate bottom of comb onto underside of unit until it snaps into locking groove.Troubleshooting If your clipper/trimmer does not seem to be operating properly, please check the following:Check the outlet's current by plugging in another appliance (one you know is in proper working condition) into the outlet.Make sure the unit is not connected to a power source that turns itself off when lights are turned off.Verify that the blade assembly moves freely and is mounted properly.If you still encounter problems with your unit, ship your clipper prepaid to the Wahl factory with a note explaining the problem:Attn: Repair DepartmentWahl Annex3001 Locust StreetSterling IL 61081.Read and follow all instructions, precautions, and warnings on product, including clipper oil and accessories.
Wahl Tid-Bit Pet Clipper/Trimmer Kit
