UL listed.Important SafeguardsWhen using an electrical appliance, basic precautions should always be followed, including the following. Read all instructions before using this appliance.Danger: To reduce the risk of death or injury by electric shock:An appliance should never be left unattended when plugged in.Do not reach for appliance that has fallen into water. Unplug it immediately.Do not use while bathing or in a shower.Do not place or store appliance where it can fall or be pulled into tub or sink. Do not place or drop into water or other liquid.Always unplug this appliance from electrical outlet immediately after using.Unplug this appliance before cleaning.Warning: To reduce the risk of burns, fire, electric shock, or injury to person:Close supervision is necessary when this appliance is used by or near children or invalids.Use this appliance only for its intended use as described in the manual. Do not use attachments other than those recommended by the manufacturer.Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the appliance to a Service Center for examination and repair.Keep the cord away from heated surfaces.Never operate this appliance with the air openings blocked or while on a soft surface, such as a bed or couch, where the air openings may be blocked. Keep the air opening free of lint, hair, and the like.Never drop or insert any object into any opening.Do not use outdoors or operate where aerosol (spray) products are being used, where oxygen is being administered or near flammable liquids, such as certain flammable blade lubricants or cleaning agents.Do not use this appliance with a damaged or broken comb or blade set, as injury may occur.Do not place or leave appliance where it may be damaged by an animal or exposed to weather.To disconnect, turn all controls to off then remove plug from outlet.Save The InstructionsThis clipper was designed for commercial use.Facts About Blades and OilingBlades not only become dull from cutting hair--they are dulled by the abrasive particles on the hair, dirt, sand, etc.Blades will not cut if abrasive particles are picked up and carried by the oil film between the blades. These particles tend to hold the blades apart and cause chewing and pulling instead of clean cutting.Oiling the blades performs two distinct functions:Provides a low friction, very thin lubricant film between the cutting blades so that they can take a full cutting stroke without becoming hot from friction.Flushes abrasive particles and hair out from between the blades.Note: If you cut into dirt, immediately wash with oil to flush it out.Wahl strongly recommends Wahl H-42 as a cleaner and a lubricant.Servicing Of A Double-Insulated ApplianceIn a double-insulated appliance, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated appliance, nor should a means for grounding be added. Servicing a double-insulated appliance requires extreme care and knowledge of the system, and should be done only by qualified service personnel. Replacement parts must be identical to those parts being replaced. A double-insulated appliance is marked with the words "double insulated". The symbol for double-insulated products may also be marked on the appliance.Cleaning and General CareBefore cleaning/maintenance, switch the equipment off and remove the main plug from the socket.Never immerse the unit in water.Each time after use remove any hairs from the cutting blade using the cleaning brush.Clean the body of the clipper with a soft, damp cloth. Never use solvents or scouring agents.The cutting head should be cleaned and oiled frequently with Wahl H-42 in order to maintain its good cutting performance and thus ensure a long service life.The cutting head should be replaced if the cutting performance is reduced after extended use despite regular cleaning and lubrication.During use always be sure the cord is not twisted or running over any sharp objects that might cut the cord insulation.CordIf your clipper has a polarized plug: To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug fits in a polarized outlet only one way. In the event the plug does not fit fully in the outlet, reverse the plug. In the event it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.Cleaning The Air FilterClean the air filter once a week or more often if necessary.Remove filter cover and clean air filter with cleaning brush.Snap the filter cover onto the clipper until it click locks into place.Changing The Cutting Head (Blade)The cutting head can be removed by pressing the gray button under the blade and pushing the blade away from the housing. The clipper should be switched off before removing blades.To Refit the Blade Set the clipper should be turned on and running.Fit the blade into the metal guide and press it into place. There will be a definite click when the blade is snapped in place.Read and follow all instructions, precautions, and warnings on product, including clipper oil and accessories.
Wahl KM2 Speed Animal Clipper Kit
