Innotek Free Spirit Deluxe Advanced Trainer

Quick Start GuideStep 1: Power UpCharge the collar 12 to 14 hours. Be sure to cover the charge jack with the gray plug when done. Insert batteries in the transmitter positive (+) side out.Step 2: Match ComponentsRemove receiver from charger. Light will flash yellow. Press button on transmitter within 30 seconds. The components now work together.Turning the Collar ON and OFFBefore putting collar on dog, briefly touch the two red paper dots together to turn the collar on.ON: A brief, solid green light and tone indicate that the collar is on, ready to use. A green light will blink while the collar is on.OFF: A brief, solid red light and tone indicate the collar has been turned off.Step 3: Adjust the CollarProper Fit: The collar fit should be snug, yet loose enough to allow one finger to fit between the strap and dog's neck. Fit is important because a loose collar may cause inconsistent performance. It's okay to trim any excess strap length.Digital Advanced TrainersModels ADV-300P, ADV-1000P, ADV-1002Understanding the TransmitterThis hand-held device signals the collar receiver to produce stimulation and/or tone. The transmitter is water-resistant and should not be immersed in water or placed in a dishwasher.Transmitter Buttons: ADV-300P and ADV-1000P UsersContinuous: You control the length of stimulation by the time you press the button. For a short stimulation, press and release the button. For a longer stimulation, hold the button down. A maximum of ten seconds may be applied before the safety feature to prevent over-correction engages. After ten seconds, stimulation will be locked out for another ten seconds.Momentary: Delivers a brief, pre-measured tap.ID: Selects a random ID code from 2,048 available in case you experience interference problems from other nearby training units. Press and hold the button for three seconds. The display will show the letters PROG and quickly scroll through numbers and then go blank. A new code has been selected. Re-match the components as described in Step 2 of the Quick Start Guide.Tone: Produces a tone from the collar. No stimulation is delivered.Level Up: Increases stimulation level.Level Down: Decreases stimulation level.ADV-1002 UsersDog 1--Provides stimulation for Dog 1: Uses continuous stimulation, meaning that you control the length of stimulation by the time you press the button. For a short tap, press and release the button. For a longer signal, hold the button down. A maximum of ten seconds may be applied before the safety feature to prevent over-correction engages. After ten seconds, stimulation will be locked out for another ten seconds.Dog 2--Provides stimulation for Dog 2: Also uses continuous stimulation.Level Up: Increases stimulation level for the dog indicated in that column.Level Down: Decreases stimulation level for the dog indicated in that column.The Digital DisplayWhen either the continuous or momentary buttons are pushed (1 or 2 on the ADV-1002), the display will indicate the stimulation level being transmitted. For ADV-1002 users, after the stimulation button is released, the dog number (Dog 1/Dog 2) and stimulation level will alternate briefly.When the Level UP or Level DOWN button is pushed, the display will show the new level of stimulation.LO BAT appears when the transmitter batteries need to be replaced.ADV-300P and ADV-1000P UsersWhen the tone button is pressed, a small bar will appear to the left of the stimulation level 0 as no stimulation is being delivered.Replacement BatteriesThe ADV transmitters use two 6-volt alkaline batteries. These are commonly available where you bought your unit, where batteries are sold, or call 1-800-826-5527 to order direct from Innotek.Understanding the ReceiverThe ADV units use an LED light to let you know the status of the collar.Blinking green light: collar is on and ready to use.Pulsating red light: stimulation is being delivered.Pulsating green light: tone only being delivered.Blinking red light: low battery; charge as soon as possible.Solid green light: over-correction timeout; wait ten seconds.Blinking yellow light: collar should be matched to transmitter.Testing the ReceiverHold the test light across the receiver probes.Press the transmitter button for stimulation.Test light will illuminate for the length of time stimulation is being delivered.The intensity of the light will increase as the level increases.Charging the ReceiverThe receiver has a long-life NiMH battery. It will take 12 to 14 hours to fully charge and will operate up to 72 hours between charges depending on use and temperature. Extreme temperatures (hot or cold) can significantly affect battery life. Always charge at room temperature.Collar should be fully charged once every two to three months.The receiver will need to be matched with the transmitter after charging. Follow Step 2 of the Quick Start Guide.Matching the Transmitter and ReceiverLocate the red dot on transmitter and on receiver. Hold components together at the dots until the receiver LED glows green then amber. Press transmitter button; receiver LED will glow red and deliver stimulation. The components now work together. For the ADV-1002, do this step for Dog 1 using the yellow collar and Dog 2 using the black collar. Perform this step each time you charge the receiver collar, or replace transmitter battery. Register Your ProductYour product can be registered on the Innotek website at www.innotek.net. Important AdviceRead the complete instructions and follow all directions. If you have any questions, please call 1-800-826-5527.This device is intended for use only on dogs. Never attempt to use it for any purpose not described in the manual.Never perform set-up procedures while the collar is on your dog.Any collar worn for extended periods can cause a condition similar to bedsores, known as pressure necrosis. To reduce the possibility, you must do the following:Never leave the collar on the dog for more than 12 consecutive hours.Examine the dog's neck daily for any signs of a rash or a sore.Supervise your dog during the first two days of training. Check the fit to prevent excessive pressure; you should be able to insert one finger between the collar strap and your dog's skin. Wash the dog's neck area and the probes of the collar weekly with a wash cloth and mild hand soap; rinse thoroughly. If the condition persists beyond 24 hours, see your veterinarian. Always use the rubber insulators between the collar strap and probes to provide insulation in damp conditions. Other collars and metal tags should be removed when using the remote training collar as they may interfere with proper operation. Do not attempt to dismantle or repair any components of this system; doing so will void the warranty in full. The computerized circuitry should be serviced only by an authorized expert.