InstallationCaution: Disconnect the plugs of all the appliances inside the aquarium before putting your hands in the water.Water Circulation OperationPowerhead 10Remove the motor cover and the impeller cover. Install the three suction cups in the holes on the back panel of the pump. Put the covers back on. Securely place the pump against the glass of the aquarium by pressing firmly to ensure that the pump holds. Install the hose adapter. Use the sliding bar at the bottom of the pump to control the flow of water.Powerhead 20 & 30Powerheads 20 and 30 come with an adjustable rim attachment and a suction cup bracket. The adjustable rim attachment is designed to be fastened on most aquarium frames. The suction cup bracket allows custom installation where it is not desirable to clamp the powerhead over the rim of the tank. Use the part that is best suited for your needs. The powerhead can easily slide into either part for secure installation.Undergravel Filter OperationPowerhead 10Remove the motor cover and the base cover. Install the three suction cups in the holes on the back panel of the pump. Put the covers back on. Attach the swiveling elbow connector (if required to align the water intake to the riser stem of the undergravel filer) and the stem adapter to the powerhead. Set the stem adapter (with powerhead attached) into the undergravel riser stem and then firmly press the suction cups against the aquarium glass.Powerhead 20 & 30Determine the difference in height between the rim of the aquarium and the seated position of the stem adapter in the undergravel filer stem (about 3 1/2"). Cut or adjust the undergravel filter stem to the correct height. Seat the powerhead stem adapter in the undergravel filter stem and rotate the clamp knob on the adjustable rim attachment to securely tighten the clamp to the required aquarium rim width. If you are using the suction cup bracket, install it by pressing it firmly against the aquarium glass and then slide in the powerhead.Quick Filter OperationThe powerhead can easily be converted to a Quick Filter to remove dirt and debris quickly. The Quick Filter can be obtained from your local pet dealer. Place a Quick Filter cartridge in the Quick Filter attachment (if not already installed).Powerhead 10Place the swivel elbow stem connector over the intake of the pump. Firmly attach the Quick Filter to the swivel elbow stem connector.Powerhead 20 & 30Firmly insert the powerhead strainer plate into the Quick Filter. Place the unit in the aquarium in the desired location and clamp or use suction cups to keep in position. After all proper installation procedures are completed, connect the power cord to the electrical outlet.Note: Aquariums which use very fine grade gravel or sand may require nylon mesh placed over the strainer to prevent the powerhead from clogging.Important: The powerhead must operate continuously to sustain filtering action and beneficial bacteria. Do not unplug the powerhead for periods in excess of one hour to avoid the reduction of the biological filtration.Important SafeguardsWarning. To guard against injury, basic safety precautions should be observed when handling the powerhead, including the following:Read and follow all safety instructions and all important notices on the appliance before using, for the complete enjoyment, use and understanding of this product. Failure to do so may result in loss of fish life and/or damage to the unit.Danger. To avoid possible electric shock, special care should be taken since water is employed in the use of aquarium equipment. For each of the following situations, do not attempt repairs yourself; return the appliance to an authorized service facility for service or discard the appliance.If the water pump falls into the water, don't reach for it. First unplug it and then retrieve it. If electrical components of the appliance get wet, unplug the appliance immediately.If the water pump shows any sign of abnormal water leakage, immediately unplug it from the power source.Carefully examine the appliance after installation. It should not be plugged in if there is water on parts not intended to be wet.Do not operate any appliance if it has a damaged cord or plug, or if it is malfunctioning or dropped or damaged in any manner. The power cord of this appliance cannot be replaced; if the cord is damaged, the appliance should be discarded. Never cut the cord.To avoid the possibility of the appliance plug or receptacle getting wet, position the appliance to one side of a wall-mounted receptacle and prevent water from dripping onto the receptacle or plug. A drip loop should be arranged for the cord connecting appliance to receptacle or the connector if an extension cord is used, to prevent water traveling along the cord and coming in contact with the receptacle.If the plug or receptacle does get wet, don't unplug the cord. Disconnect the fuse or circuit breaker that supplies power to the appliance. Then unplug and examine for presence of water.Close supervision is necessary when any appliance is used by or near children.To avoid injury, do not touch moving or hot parts.Always unplug an appliance from outlet when not in use, before putting on or taking off parts, and before cleaning. Never yank cord to pull plug from outlet. Grasp the plug and pull to disconnect.This is an aquarium pump. Do not use an appliance for other than intended use (i.e. don't use on swimming pools, garden ponds, bathrooms, etc.). The pump is suitable for use in water with temperature up to 35øC. The use of attachments not recommended or sold by the appliance manufacturer may cause an unsafe condition.Do not install or store the appliance where it will be exposed to the weather or to temperatures below freezing.Make sure an appliance mounted on a tank is securely installed before operating it.Read and observe all important notices on the appliance.If an extension cord is necessary, a cord with proper rating should be used. A cord rated for less amperes or watts than the appliance rating may overheat. Care should be taken to arrange the cord so that it will not be tripped over or pulled.Caution: Powerhead must not run dry.Save the instructions.Read and observe all manufacturer warnings, precautions, instructions, directions, and notices for safety and operation included with and on product.Made in Italy.
AquaClear Power Head Multifunctional Water Pump 50
Aquarium Size: For 20-50 gallon Aquariums
Gallons Treated: 270 GPH
Model: Model 50
AquaClear Power Head Multifunctional Water Pump 70
Aquarium Size: For 40-70 gallon Aquariums
Gallons Treated: 400 GPH
Model: Model 70
AquaClear Power Head Multifunctional Water Pump 20
Aquarium Size: For 5-20 gallon Aquariums
Gallons Treated: 127 GPH
Model: Model 20
AquaClear Power Head Multifunctional Water Pump 30
Aquarium Size: For 10-30 gallon Aquariums
Gallons Treated: 175 GPH
Model: Model 30
